Vista 15” TFT LCD MONITOR
USER
MANUAL
MODEL: VFSM15
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different form that to which
the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
Shielded interface cables and AC power cord, if any, must be used in order
to comply with emission limits.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user‘s authority to operate the equipment.
SAFETY PRECAUTIONS
1. Do not modify the three-prong grounding type monitor power plug in any way.
2. Operate this unit only from the type of power source indicated on the label.
3. Do not block or cover ventilation openings on the back or bottom of the
monitor cabinet.
4. Do not place this monitor near a radiator or heating vent.
5. Do not push objects of any kind through cabinet openings. This may result in
fire or electrical shock.
6. Before adding attachments always ask a service technician to perform
routine safety tests to determine that equipment is in safe operating
condition. Ground potential tests should be part of the routine safety check
made by the service technician.
7. Do not place monitor on an unstable cart, stand, or shelf where it may fall
and injure personnel or damage equipment.
2
8. Route power cords so that they cannot be walked upon or tripped over. Do
not allow anything to rest on the power cord.
9. Do not install monitor in wet areas, or where it may be exposed to rain or
water. Do not spill liquid of any kind on the unit.
10. Unplug the power cord from the unit before cleaning the display. Use only
a damp cloth. Do not use alcohol, spirits, or ammonia to clean the display.
DO NOT ATTEMPT TO CLEAN THE INTERIOR OF THIS UNIT-THIS ACTION
MUST BE PERFORMED BY THE SERVICE TECHNICIAN AS REQUIRED
DURING NORMAL MAINTENANCE.
11. Refer all servicing to qualified service personnel. REMOVAL OF BACK
COVER BY UNAUTHORIZED PERSONNEL MAY EXPOSE THE USER TO
DANGEROUS VOLTAGES OR OTHER HAZARDS.
12. Unplug the unit immediately and notify the service technician.
A. If liquid has been spilled into the display or the display has been
exposed to rain or water.
B. If the unit has been dropped or the cabinet damaged.
C. If fuses continue to blow.
D. If the power cord is damaged or frayed.
E. If a distinct change from normal operation is apparent.
When replacement parts are required, be sure that the service technician
uses components specified by the manufacturer which have the same
characteristics as the original parts. UNAUTHORIZED SUBSTITUTIONS MAY
RESULT IN FIRE, ELECTRICAL SHOCK OR OTHER HAZARDS.
Upon completion of any service or repairs, ask the technician to perform
safety checks to determine that the equipment is in safe operating condition.
WARNING: SERIOUS SHOCK HAZARDS EXIST WITHIN THE COVERS OF
THIS MONITOR. DO NOT OPEN THE COVERS UNDER ANY CIRCUMSTANCES,
THERE ARE NO USER SERVICEABLE COMPONENTS INSIDE
3
1.GENERAL FEATURES
This is a high performance 15" TFT LCD monitor with a 1024x768 XGA resolution. The LCD monitor
has been designed for use with both PC and security systems, comply with the power management
regulations of VESA DPMS, supported by Plug & Play, complying with DDC1/2B.
FEATURES
90~264V AC Power Supply
NTSC/PAL Auto-Detector
High Resolution
PC Input
Dual Video Input/Output
Dual Audio Input/Output
Y/C Input
Up to 16M Colors
Built-in Auto Channel Scanning
OSD With Multiple Languages
Wall Mountable
4
2.SETTING UP
Read this chapter for important safety information and how to set up and connect the display to your
computer or camera.
¾Check the attachment of monitor. There are power cord, user’s manual and PC signal cable.
¾Make sure the surface for placing the LCD monitor is stable and level.
¾Keep the monitor away form sources of liquids and moisture.
¾Keep the monitor’s vents free from obstruction.
¾If you will not be using the monitor and computer for a day or more, make sure to turn off the
computer and turn off the main switch of the monitor.
2.1 CONNECT THE MONITOR TO YOUR COMPUTER
¾Make sure the computer is turned off.
¾Plug in the monitor.
¾Connect the PC signal cable of the computer to the monitor.
¾Turn on the computer.
¾Turn on the main switch of the monitor.
¾Push the power button in front of the monitor.
¾Push the channel button to display PC input signal.
2.2 CONNECT THE MONITOR TO THE VIDEO SOURCE
¾Plug in the monitor.
¾Connect the video signal to the monitor.
¾Turn on the main switch of the monitor.
¾Push the power button in front of the monitor.
¾Push the channel button to display video input signal.
5
3.CONTROLS AND INDICATORS
3.1 FRONT PANEL
a. CHANNEL BUTTON
¾Select channel ¾Press this button to choose the channel to be displayed.
¾Auto scan ¾Press the button over 2 seconds until the power LED changes to yellow color.
b. MENU BUTTON
¾Press the button to show the main OSD menu.
¾Press the button for the second time to show the sub OSD menu after the main menu is elected.
c.
¾Press
BUTTONS
buttons to select an icon in the main menu.
buttons to adjust the selected icon value in sub menu.
¾Press
d. POWER LED
¾Green – Power on
¾Dark – Power off
¾Yellow – Auto scan mode
¾Yellow (Flashing) – Power saving
e. POWER BUTTON ¾Press the button to turn on or turn off the monitor.
6
3.1 BOTTOM PANEL
a. PC input
b. Y/C input
c. Video(CVBS) 1 input
d. Video(CVBS) 1 output
e. Video(CVBS) 2 input
f. Video(CVBS) 2 output
g. Audio L input
h. Audio L output
i. Audio R input
j. Audio R output
7
4
ON SCREEN DISPLAY (OSD)
4.1
PC MODE
Press
buttons to select an icon, then Press MENU button to change the values
in the sub menu.
C O N T R A S T
>>>
RGB
(((
)))
EXIT
1 0 2 4 X 7 6 8
4 8 K
6 0 H Z
CONTRAST ¾Press
buttons to adjust the contrast value, then press MENU
buttons to adjust the brightness value, then press
button to return to the main menu.
BRIGHTNESS ¾Press
MENU
button to return to the main menu.
H POSITION ¾Press
buttons to adjust the horizontal position value of the
image, then press MENU button to return to the main menu.
V POSITION ¾Press
buttons to adjust the vertical position value of the image,
then press MENU button to return to the main menu.
| | |
PHASE ¾Press
buttons to adjust the phase value, then press MENU button to
return to the main menu.
>>>
CLOCK ¾Press
buttons to adjust the clock value, then press MENU button to
8
return to the main menu.
9
RGB
COLOR ¾Press
buttons to select a color and press
buttons to
adjust the value of selected color, then press MENU button to return to the main menu.
AUTO ADJUST ¾Automatic adjusting of H position, V position, phase and clock values.
TRUE COLOR ¾True color can upgrade the panel’s color from 262K to 16M and vice
versa.
VOLUME ¾Press
buttons to adjust the volume value, then press MENU
(((
)))
button to return to the main menu.
OSD H POSITION ¾Press
buttons to adjust the horizontal location of OSD,
then press MENU button to return to the main menu.
OSD V POSITION ¾Press
buttons to adjust the vertical location of OSD,
then press MENU button to return to the main menu.
LANGUAGE ¾Select the language to be used in OSD.
RECALL COLOR ¾Recall the values of R,G,B colors. Set the color temperature of the
LCD monitor for the CIE coordinate 9300˚k or 6500˚k.
RECALL MODE DATA ¾Recall the H position, V position, phase and clock values of the
mode data.
EXIT
EXIT ¾Exit OSD menu.
10
4.2 Video mode
Press
buttons to select a icon, then Press MENU button to change the
values in sub menu.
B R I G H T N E S S
RGB
(((
)))
>>
EXIT
C V B S 1
I N P U T
BRIGHTNESS ¾Press
buttons to adjust the brightness value, then press
MENU button to return to the main menu.
CONTRAST ¾Press
buttons to adjust the contrast value, then press MENU
button to return to the main menu.
RGB
COLOR ¾Press
buttons to adjust the color value, then press MENU button
to return to the main menu.
TINT ¾Press
return to the main menu.
buttons to adjust the tint value, then press MENU button to
buttons to adjust the sharpness value, then press
SHARPNESS ¾Press
>>>
MENU button to return to the main menu.
(((
))
VOLUME ¾Press
buttons to adjust the volume value, then press MENU
button to return to the main menu.
SEQUENCE TIME ¾Press
buttons to adjust the sequence time value, then
press MENU button to return to the main menu. Sequence time is the displaying time for
each channel in auto scan mode.
11
TRUE COLOR ¾True color can upgrade the panel’s color from 262K to 16M and vice
versa.
OSD H POSITION ¾Press
buttons to adjust the horizontal location of OSD,
then press MENU button to return to the main menu.
OSD V POSITION ¾Press
buttons to adjust the vertical location of OSD,
then
press MENU button to return to the main menu.
LANGUAGE ¾Select the language to be used in OSD.
RECALL ¾Reset all of the values to factory preset values.
TITLE ENABLE ¾Enable to show the title message while OSD menu disappear.
TITLE EDITING ¾Editing title message of the channel. Select a channel then press MENU
button into next sub menu
.
T I T L E
E D I T I N G
Y / C
C V B S 1
C V B S 2
EXIT
There are 16 characters that can be edited in each channel. Press
select character on location and press
then press MENU button to return to the sub menu.
buttons to
buttons to change the character in that location,
T I T L E
E D I T I N G
C V B S 1
F R O N T
D O O R
EXIT
EXIT ¾Exit OSD menu.
5.SPECIFICATIONS
12
Type
LCD Panel
15” TFT Color
262K colors
Colors
Viewable Size
Dot Pitch
15" 304.1mm (H) x 228.1mm (V)
0.297mm x 0.297mm
60/60/45/55
Viewing Angle(L/R/T/B)
Contrast Ratio
Brightness
300:1
200 cd/m2
Resolution
1024 x 768
User's Controls
Power
Power, Channel, Menu, Up, Down, Left, Right
Power, Auto_Adj, Menu, Up, Down, Left, Right
Input voltage
AC 90 to 264V ( 60 / 50Hz) or DC 12V
Consumption
Normal: 35W(max); Standby: 5W(max)
Agency Approval
Others
ETL, ETL-C, FCC, CE
Weight
5kg(NW), 6.5kg(GW)
Dimensions
(WxHxD)mm
Depth
395x395.3x182.1(Physical),
468x508x268(Package)
70mm
Temperature
Operating Conditions
Storage Conditions
10
20 % to 85 % (Non-condensation)
-20 to 60
to 40
Humidity
Temperature
Humidity
5 % to 95 % (Non-condensation)
Level 0.7Vp-p / 1KHz (typical), RCA Jack
Loop-through type, RCA Jack
Audio x 2
Audio x 2
Audio Input
Output
Stereo 2 x 1 watts, built-in speakers
Video(CVBS) x 2
Capability
Video Input
Composite video 1.0Vp-p / 75Ω, RCA Jack
Y/C x 1
Level 1.0Vp-p / 75Ω, Mini-din 4pin connector
Video(CVBS) x 2
Output
OSD
Loop-through with buffered circuit, RCA Jack
Brightness, Contrast, Color, Tint, Sharpness, Volume, Sequence Time
True Color, OSD H Position, OSD V Position, Language, Recall, Title
Enable
Title Editing, Exit
Operation System
Compatibility
NTSC M / PAL BGHI
Scanning Frequency
NTSC 15750Hz ± 500Hz / 60Hz
PAL 15625Hz ± 500Hz / 50Hz
PC
Input
OSD
Analog RGB signal : 0.707Vp-p / 75Ω, D-sub 15 pin
Contrast, Brightness, H Position, V Position, Phase, Clock, Color, Auto
Adjust
True Color, Volume, OSD H Position, OSD V Position, Language, Recall
Color
Recall Mode Data, Exit
DDC1/2B
Plug & Play
VESA DPMS
Power Management
Supported Timing
640x350x70Hz
640x480x60Hz
640x480x75Hz
720x400x85Hz
800x600x72Hz
832x624x75Hz(MAC)
1024x768x75Hz
640x400x70Hz
640x480x72Hz
720x400x70Hz
800x600x60Hz
800x600x85Hz
1024x768x70Hz
1024x768x85Hz
640x400x56Hz
640x480x66Hz(MAC)
640x480x85Hz
800x600x56Hz
8800x600x75Hz
1024x768x60Hz
1024x768x75Hz(MAC)
13
3121-0301-03
REV: 01
-15-
|